Kanger Cupti Review

Best Deal: $54.95 from DirectVapor
Use our link and get a 5% discount.

Best Vape Mods of 2016

8.8 Total Score
Kanger CUPTI Review Bottom Line

Kanger CUPTI is an All-in-One 75W TC mod with built-in tank with CLOCC atomizer feature. It is based on kangertech’s very first temperature control device the NEBOX and it addresses the leakage problem that the NEBOX had. The Cupti did not show signs of leakage. Performance is great and clouds are enormous. Good choice!

Best Deal: Buy from an Authorized Dealer - DirectVapor. Use our link and get a 5% discount.


In-Depth  Kanger Cupti Review:

Kangertech’s latest device the all in one temperature control, Kangertech CUPTI Starter Kit. It is based on kangertech’s very first temperature control device the NEBOX. And Kanger did address the leakage problem that the NEBOX had – where the NEBOX filled from the bottom which was the source of the eJuice leakage problem.

First Impression

Kanger Cupti InstructionThe CUPTI has a wattage range of 70 to 75W and in Temperature Control mode has a range of 200 to 600°F (100-300°C). Power adjustments are in 0.1-watt increment and temperature adjustment is 10°F / 5°C.

CUPTI has Three ButtonsOne is the firing button which is on the front side at the most top for easy use. The other Two are the temperature increase and decrease button (‘+’ and ‘–‘) which are on the top of the unit between the display and 510 threaded pin. A single 18650 battery powers the CUPTI and Kanger does include a charging cable that connects to the device via micro USB cord at the bottom of the unit. The battery door is spring loaded which is located at the bottom of the device. Kanger includes a wide bore drip tip installed on the device, the stainless steel coil pre-installed inside the device. They also included a second drip tip which is significantly smaller or otherwise known as a standard 510 driptip, a Nichrome coil, your charging cable and a pretty comprehensive manual which shows you about how to fill it, changing your coils and gives you all the specs of this unit, etc.

Vapor Quality

Kanger Cupti

The CUPTI is a solid performer it produces a solid amount of vapor and the flavor from the Stainless Steel coil is rich and full. The buttons work well, the display is crisp and easy to read especially it’s on the top of the unit, switching between coil types, temperature control, and variable wattage modes are simple and intuitive. There was a gurgling noise and spatter of eJuice at first used but it will subside if frequently used.

Features

Kangertech gave the CUPTI pretty decent features. It will fire a wide range of coils and temp control, and has that maximum power output of 75W, 2 coils are included in the box – that is the 0.5Ohm Stainless Steel CLOCC and a 1.5Ohm Ni-chrome CLOCC. It’s worth pointing out that Kanger is also going to release a CLRBA “CHILD LOCK Rebuildable Atomizer” for the CUPTI.

Kanger Cupti OLED Display

I do like the placement of the LCD Display on the top of the device, makes it really easy for me to see when vaping. And the adjustment buttons on top makes it resistant from pressing accidentally the temperature settings and etc,

Kanger includes a charging cable which is good but they put that micro-USB port at the bottom of the device which makes it impossible to have it charging on sitting upright – you have to lay it down to charge.

Leakage-Free

Kanger Cupti Max Fill

At first, I was in doubt that CUPTI will have the same leakage problem like it did on NEBOX. However, I have used this unit for 3 weeks now and there’s been no sign of leaking at all. I also feared that the micro-USB port on the bottom of the device can cause seepage when charging since the placement of the port is on the bottom, you have to charge the CUPTI laying one side. Plus, it has an internal tank and it can’t be remove – chances are? You might have some eJuice running while charging it.

BUT I HAVE NOT EXPERIENCE ANY LEAKING OR WHATSOEVER EVEN WITH THE CUPTI LAYING ON IT SIDE OVERNIGHT WITH EJUICE ON THE TANK.

If you’re looking for an all-in-one temperature control device but cut-off by criticism of the NEBOX, the CUPTI maybe just the thing you are waiting for. I totally recommend purchasing the Kanger CUPTI from DirectVapor. By using our link, you will get 5% discount on theCupti. Discount will be applied automatically after you add the product to your cart. Buying from an Authorized Dealer is always one of the safest options.
Kanger Cupti Kit

Buy at DirectVapor and use our link and get a 5% discount.

$54.95

15 Comments
  1. Reply
    Taylor September 25, 2016 at 8:49 pm

    My Cupti keeps gurgling and spitting e-juice, and I’m not sure how to fix it. No matter what I do, it keeps doing it. Making it painful to use due to the hot juice being spurted from the mouth piece. But I love it when it’s working! Can someone help with the spitting and gurgling issue? Thanks in advance!

    • Reply
      Kriss.lovex February 14, 2017 at 2:55 pm

      Use a qtip and clean the drip tip and the drip tip hole, also use a qtip and stick it down the air shaft whole it’s together with juice in it sometimes it floods when you pull too hard, seems to solve the problem….then repeat every time you reload.

    • Reply
      mrsoft November 7, 2016 at 6:20 pm

      When it starts spitting, turn it upside down for about 30-60 seconds. Some e-liquid may or may not drip out the mouth piece, but it usually solves the issue either way.

      Another issue that occurs alot to me is that it starts tasting burnt.
      if this happens, open the ecig, like when you are about to refill, then screw it back on.

      yet another issue is when it starts showing check battery no matter how much you charge it.
      I solved this by emptying the ecig of liquid, and then cleaning the battery, the coil.. basically all the lose parts, and refilling it half-way up to the max marker (first time only)

    • Reply
      Prince Roger Nelson October 12, 2016 at 7:07 pm

      I’ve had mine for 3 weeks now with no leaks and will be changing out the coil for the 1st time. The gurgling has been happening to me as well when i refill with juice. I’ve found the perfect solution for me is…I roll a piece of paper towel and roll it tight. I twist it while lowering it down the drip tip so it can absorb the the juice that’s inside the coil. I normally have to do this twice and the gurgling is resolved.

      • Reply
        red beard February 8, 2017 at 1:25 pm

        i use a q-tip

      • Reply
        Anastasia February 3, 2017 at 1:02 am

        No leaking. No gurgling (not for me at least. And I’m a major chain vapor!!!) I absolutely love it. I have higher end mods and RBA’s. I make some pretty great builds (if I must say so myself lol!) but I needed something with more simplicity.. rather then changing tanks or when using an RBA. Having to wind up build a coil on the fly if I don’t have any made and with me.
        I would compare this to my snow wolf mini as far as the wattage and TC etc. and I will always love my original snow wolf mods. Big and mini.
        But this mod- has become a game changer for me. I’m able to throw a couple batteries in the plastic battery case. Put them in my purse. (I always grab some juice and a coil just in case. But never have I needed to change the coil while out and about or during the work day).
        If I leave home with a full tank and a full battery. It gets me thru all day into the night before I have to change the battery and fill it up some.
        By far one of the best vaping purchases I’ve made to date. (And I’ve been late in the game with the AIO devices Bc I couldn’t decide which one I wanted)
        When the Nebox came out I wanted it so bad. But I was too worried about the leaking. So I didn’t order it. Then a couple more surfaced but reviews were mixed. One was hard to find. (The summit by artery)
        And once the Cupti came out. I knew I would eventually get it. Well I did and I couldn’t be happier. It’s a great device. I don’t need 300w or even 200w!!
        I just wish they made the CLRBA they said they would. I can’t find it anywhere. I’ve found ones that aren’t genuine kangers. But I steer clear of the knock off stuff (personal opinion only) bc I’m unsure of the safety and don’t know who’s actually making it.
        IF they come out with an CLRBA for the Cupti. I’ll be most definitely purchasing it. That would be the icing on an already very nice and tasty cake!!
        As for vapor production… the little mod packs some really nice clouds!!!
        My sister who just started vaping loved the simplicity of my Cupti so much. She got one. It’s great for beginners and veteran vapors. She now using the subohm coils… and not the smaller tip or restricting the air flow
        And I had some great barely used mods I was gonna give her to get herself going! But she didn’t like the idea of a mod and tank and coil and for some batteries.
        The AIO is the way she went and she’s now smoke free for almost 3. Maybe 4 months and happily vaping her Cupti as well she in fact bought a second one in case she needed a back up!! (I think she wanted the rose gold personally lol!!)

        So if you’re unsure about purchasing this. Don’t be. You won’t be disappointed.
        As for those experiencing gurgling. I can’t really answer cause I haven’t. If I do. I’d probably make sure that all the juice was out and that the coil wasn’t flooded etc. I’m sure there’s an easy fix for it.
        Good luck. Happy Vaping!!! And go get yourself the Cupti!!
        (I definitely do not get any compensation by saying I love a product! Lol!! I just like to share a detailed honest review. Bc i know others reviews have always helped me decide!)
        Chase clouds!

  2. Reply
    Renee Schucker September 27, 2016 at 7:37 pm

    My is doing the same thing spitting and gurgling,please help,i really like everything about it but this issue. Thanks

  3. Reply
    Henri_MTL September 29, 2016 at 8:50 pm

    I use Cupti for more than 1 month and after a lot of tries of other mods especially with separated tank and battery, the Cupti is the best of the best 🙂 No leak, no more problem to change the battery (usually the tank’s screw doesn’t fit with the battery after a while like two weeks..), and buttons are very well placed.
    Definitively, the Cupti is the best way to stop the poison working with fire.

  4. Reply
    Chaz H September 29, 2016 at 10:39 pm

    I’ve had mines and it works great. To fix any gurgling. (Which usually happens after refilling or changing coils) simply hold the fire button down and blow through the cupti ( make sure air flow is wide open). This will release excess juice not being absorbed by the cotton and should fix the gurgling. In a matter of seconds. May have to blow hard 2-3 times. Easy fix. Best all in one vape on the Market in my opinion.

    • Reply
      Marina February 7, 2017 at 4:57 pm

      Good advice!

  5. Reply
    793thompson October 20, 2016 at 7:16 pm

    I just received my cupti and it works great so far very happy with the product to those who are having problems try turning it down I am a mouth to lung smoker I have my cupti set at 50watt 400 degrees works great I use a 6 tabaco

  6. Reply
    peyman October 27, 2016 at 6:06 pm

    I am Iranian and my English is not good.i have purchased a kangertech cupti instrument but it usually says check battery and I cant use it what should I do
    thanks

  7. Reply
    Frank December 4, 2016 at 3:11 am

    Im Just wondering, why did KangerTech make the cupti a 75 watt unit if you can only use 30 watt wicks. Is there something i dont know ?
    Does anyone sell other wicks that can go higher than 30 watts.
    Please guide me.
    Thanks all.

  8. Reply
    pete January 8, 2017 at 1:40 am

    I have had this CUPTI for some time now, when the tube is screwed in it puts pressure in the tank that over saturates the cotton. I simply shake it in a sweeping motion over the sink to get the excess out. Takes only a few seconds and then hits fine.

  9. Reply
    Jackob March 22, 2017 at 1:51 pm

    hey so ive just bought it, and i wonder about the coils: should i pour few drops of juice on top of the new coil before using (like i did in joyetech aio 4example) or it isnt recomended?

Leave a reply

Register New Account
Reset Password